Call us: +44 (0)1634 300900 | E-mail: sales@dpie.com

Diamond Point International

MEN Mikro GP2 - 3U CompactPCI® Serial Quad Port Gigabit Ethernet SFP PHY Line Card

4x Gigabit Ethernet on SFP, -40 to +85°C Screened

MEN Mikro GP2 - 3U cPCI Serial 4xPort GbE SFP PHY Card
Key Features
4-Port Gigabit Ethernet PHY Line Card
3U 4HP CompactPCI® Serial Board, 10/100/1000
4 Gigabit Ethernet (front) on SFP
FX / SX / LX / ZX modules supported
LEDs for front port and board states
EN 50155 class TX compliant (railways)
PICMG CPCI-S.0 CompactPCI® Serial peripheral
-40 to +85°C with screened components

Introduction

MEN Mikro's GP2 is a 3U Gigabit Ethernet PHY line card implemented as a CompactPCI® Serial board. It occupies one peripheral slot using a 4 HP front panel with four Gigabit Ethernet ports on SFP cages. The GP2 is designed to work in combination with the G101 CompactPCI® Serial managed industrial Ethernet switch.

The GP2 provides four cages for 100BASE-FX, 1000BASE-SX, 1000BASELX and 1000BASE-ZX SFP modules. Each interface supports a data transfer rate of 1 Gbit/s max and provides two LEDs to indicate the link and activity status.

The GP2 operates with a primary voltage supply of +12 V, which is provided via the rear CompactPCI® serial connector. All additional required voltages are generated onboard. It is fully compliant with the EN 50155 railway standard, qualified for a -40 to +85°C operation temperature and ready for coating.

Note: This is a line card, not a peripheral card (i.e. connects to QSGMII interfaces on CompactPCI® Serial backplane, specifically P1) - refer to block diagram for clarifiction.

Specification

Main Specification

FunctionSupported Protocols: IEEE 802.3 standard
Interface(s)Four 100/1000 Mbps SFP cages at front panel
Connection(s)Front:
• Four SFP slots, 1000BASE-SX/LX/ZX (1 Gbit/s)

Rear:
• Serial GPIO (SGPIO)
• Quad Serial Gigabit Interface (QSGMII)

Status LEDs (front):
• Two LEDs for each SFP slot
• Signal link status
• Signal link activity

Tested SFP Types
• CISCO GLC-SX-MM, 1 Gbps BASE-SX, 220/500 m, 0 to +70°C
• AVAGO ABR-5710 ALZ, 1 Gbps BASE-SX, 250/550 m, -40 to +85°C
• Finisar FTLF8519P3BTL, 1 Gbps BASE-SX, 300/500 m, -40 to +85°C
• Finisar FTLF1318P3BTL, 1 Gbps BASE-LH, 10 km, -40 to +85°C
• Finisar FTLF1518P1BTL, 1 Gbps BASE-ZX, 80 km, -40 to +85°C
• AVAGO ABR-57R5APZ, 4.25 Gbps BASE-SX, 300 m @ 2.125 Gbps, -10 to +85°C

General

ExpansionCompliance with CompactPCI® Serial PICMG CPCI-S.0 Specification
Requires peripheral slot with extensions (QSGMII)
ElectricalSupply voltages: +12 V (±10%)
Power consumption: 5 W typical (max. 15 W depending on SFP modules)

Supervision and Control
• BITE Voltage Supervision
• Voltage monitoring
MechanicalDimensions: conforming to CompactPCI® Serial specification for 3U boards
Front panel: 4HP with ejector
Conformal CoatingUpon request
SoftwareN/A
TemperatureTemperature range (operation):
• -40 to +85°C
• Airflow: 1.5 m/s
Temperature range (storage): -40 to +85°C
HumidityRelative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Weight136 g
VibrationVibration (Function): 1 m/s², 5 Hz to 150 Hz (EN 61373)
Vibration (Lifetime): 7.9 m/s², 5 Hz to 150 Hz (EN 61373)
Shock50 m/s², 30 ms
MTBF250.000 h @ 40°C according to IEC/TR 62380 (RDF2000)
Safety/CertificationFlammability
• PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMCEN 50155 (Insulation)
EN 50155 (Voltage)
EN 55022 (radio disturbance)
EN 61000-4-2 (ESD Immunity)
EN 61000-4-4 (burst)
Warranty2 Years
RoHSCompliant

Ordering Details

Board02GP02-00
3U CompactPCI® Serial, QSGMII to 4 x SFP 1GB port extender EEE and Sync-E support, -40 to +85°C
Accessories02G101-00
25-Port Gigabit Ethernet Managed Switch, 2x RJ45 + 1x SFP 2.5 Gbps on front, 10x GE + 3x QSGMII links on backplane, -40 to +85°C with qualified components

02G101-01
24-Port Gigabit Ethernet Managed Switch, 3x M12 on front, 9x GE + 3x QSGMII links on backplane, -40 to +85°C with qualified components