Call us: +44 (0)1634 300900 | E-mail: sales@dpie.com

Diamond Point International

Kontron CP6005-SA - 6U CompactPCI® Intel® Core™ 4th Gen CPU Board

Up to 16 GB DDR3 ECC SDRAM, up to -40 to +85°C Operation

Kontron CP6005-SA - 6U cPCI Inte® Core 4th Gen Board
Key Features
64-bit 4HP CompactPCI® system slot
Intel® Core™ i7, 4th generation
Up to 16GB SODIMM DDR3 with ECC
HDD and onboard flash options
4 SATA interface via rear I/O, VGA, USB
2 UARTs, dual Gb Ethernet, 1 PMC/XMC slot
Up to -40 to +85°C fanless operation

Introduction

The CP6005-SA 6U CompactPCI processor board available with Fourth Generation Intel® Core™ Quad Core processors meets the outstanding computing and graphics performance requirements at lowest power budgets.

The powerful processors enable virtualization and multithreading applications to run in full 64-bit mode using Enhanced Intel® Virtualization, Intel® HD Graphics, and Intel® Turbo Boost Technology.

Designed for bandwidth-intensive applications, the CP6005-SA provides hot swap, IPMI (Intelligent Platform Management Interface), TPM (Trusted Platform Module 1.2) support, and meets the highest standards for the management and security of high-availability applications.

This makes this board exceptionally attractive to multiple markets, including highly sensitive, security-relevant telecom and datacom applications and, thanks to its robust construction, is also ideal for image-processing systems in medical and defense systems, among many other vertical segments.

Specification

CPU

CPU SpecIntel® Core™ i7/i5 Processor 4th Generation
ChipsetMobile Intel® QM87 Platform Controller Hub
MemoryUp to 16GB SODIMM dual channel DDR3L memory with ECC and data speed of up to 1600 MHz per channel
GraphicsIntegrated into CPU with GT2 or GT3 depending on CPU type
DSUB connector for analog monitors on front
2x DVI/HDMI on rear
NetworkFront: Three 1000BASE-T Ethernet channels
Rear: Two PICMG 2.16 I/O 1000BASE-T ports
StorageNAND Flash: Socket for optional Kontron Solid State Drive up to 64GB SLC fl ash technology
SATA:
• Four ports fixed to rear I/O
• One port routed to a standard SATA connector
• One port available for mounting an optional 2.5" HDD
USB2x USB2.0 interface on USB-A host connector
4x USB2.0 interface on rear
SerialCOM1 (RS232) routed to front panel and rear I/O
COM2 (RS232) routed to rear I/O only
Front I/O3x 1000BASE-T Ethernet channels
2x USB2.0 interface on USB-A host connector
1x RS232 serial interface on RJ45 connector
1x VGA for analog monitors
Micro Switch (For Hot Swap and reset)
Status LED: Eight bicolor (red and green) control and status LEDs, Two IPMI LEDs, One Watchdog and one thermal LED, Four GP LEDs, One blue hot Swap LED
Rear I/OJ3: 2x ETH acc. PICMG 2.16, 2x ETH, VGA, COM 1/2, 4x USB, GPIO, Speaker, fan sense
J4: CP6005-SA: not assembled; CP6005X-SA 2x 10GBASE-KR, PCIe Gen 2 x4
J5: 4x SATA, 2xHDMI, HDA, battery, fan control, additional GPIO
AudioHD audio on rear I/O
OtherWatchdog, software configurable, 125 msec to 256 sec, generates IRQ or hardware reset.
Hardware monitor for thermal control, fan speed, and all onboard voltages
RTC battery backup
IPMI 1.5-compliant for IPMI based management and CompactPCI® System Management PICMG 2.9 R1.0
Trusted Platform Module (TPM) 1.2 for enhanced hardware and software based data and system security
BIOSAMI uEFI, setup console redirection to serial port (VT100 mode) with CMOS setup access, EFI Shell support, board configuration via Shell, diskless, keyboardless, videoless operation

General

ExpansionCompactPCI® Bus: PICMG 2.0 Rev. 3.0 compatible, 64-bit / 66 MHz, Universal V(I/O) 5V or 3.3V signalling, Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CompactPCI® bus)
CompactPCI® Core Specification PICMG 2.0 Rev. 3.0
CompactPCI® Hot Swap Specification PICMG 2.1 R2.0
CompactPCI® System Management PICMG 2.9 R1.0
CompactPCI® Packet Switching Backplane PICMG 2.16 R1.0

PMC/XMC: One 64-bit / 133 MHz PMC slot, Pn1-Pn4, rear I/O Pn3 to J4, 3.3 volt V(I/O). Alternatively one XMC slot via P15, supporting XMC.3 x8 PCI Express®
ElectricalUp to 60 watts (quad core), up to 50 watts (dual core) or less, depending on CPU type
Mechanical233 x 160 x 20.5 mm, 6U, 4HP
Conformal Coatingon request
SoftwareSupport for Windows® 7, Windows® Server 2008R2, Linux®, VxWorks (other OSs may be possible, please contact us for information
TemperatureTemperature range (operation):
• 0 to +60°C passive module heat sink, requires forced airflow cooling, Extended temperature on request
Temperature range (storage): -55 to +85°C (without battery or HDD)
Humidity93% RH at 40°C, non condensing (acc. to IEC 60068-2-78)
WeightApprox. 800gr
Altitude50,000 ft (15,240 m)
MTBF185968 h MIL-HDBK-217 FN2 Ground Benign 30°C
230420 h Bellcore Issue 6 Ground Benign 30°C
Safety/CertificationUL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950
EMCEN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2
Warranty2 Years
RoHSCompliant

Ordering Details

BoardCP6005-SA-2.4Q-8
• Quad Core 2.4 GHz, Intel® Core™ i7-4700EQ
• 8GB SODIMM dual channel DDR3L memory 1600 MHz with ECC
• Backplane connector J4 not assembled
• Temperature range 0°C to +60°C
• Standard air cooled

CP6005X-SA-2.4Q-8
• Quad Core 2.4 GHz, Intel ® Core™ i7-4700EQ
• 8GB SODIMM dual channel DDR3L memory 1600 MHz with ECC
• Dual 10Gigabit/s and PCIe Gen 2 x4 on backplane connector J4 (ZDPlus)
• Temperature range 0°C to +60°C
• Standard air cooled

CP6005-SA-1.8Q-GT3-8
• Quad Core 1.8 GHz, Intel® Core™ i7-4860EQ, GT3 graphics
• 8GB SODIMM dual channel DDR3L memory 1600 MHz with ECC
• Backplane connector J4 not assembled
• Temperature range 0°C to +60°C
• Standard air cooled

CP6005-SA-2.7D-8
• Dual Core 2.7 GHz, Intel® Core™ i5-4400E
• 8GB SODIMM dual channel DDR3L memory 1600 MHz with ECC
• Backplane connector J4 not assembled
• Temperature range 0°C to +60°C
• Standard air cooled

CP6005-SA-2.7D-8-E1X
• Dual Core 2.7 GHz, Intel® Core™ i5-4400E
• 8GB SODIMM dual channel DDR3L memory 1600 MHz with ECC
• Backplane connector J4 not assembled
• Temperature range -40°C to +70°C
• Standard air cooled
AccessoriesCP-RIO6-001
4HP Rear I/O Module for CP6005(X)-SA with 2xDVI-D; 2x USB2.0; 2x GbE; headers for 2x COM, Flash, SATA, Fan

CP-RIO6-001-HD
4HP Rear I/O Module for CP6005(X)-SA with 1xDVI-D; 2x USB2.0; 2x GbE; socket for SATA 2.5" disk; headers for 2x COM, Flash, SATA, Fan

CP-RIO6-001-HD-216
Similar to CP-RIO6-001-HD, but PICMG 2.16 compliant; without external Ethernet

CP-RIO6-001-HD-VGA
Similar to CP-RIO6-001-HD, but with VGA interface instead of DVI-D

CP-RIO6-B
4HP Rear I/O Module for CP6005(X)-SA with 2xUSB, 2xGbE; Audio, 2xCOM, DVI, HDMI, Connectors for USB Flash, 4x SATA, Fan

CP-RIO6-B-216
Similar to CP-RIO6-B, but PICMG 2.16 compliant; without external Ethernet ports

CP-RIO6-A
4HP Rear I/O Module for CP6005(X)-SA with 2xUSB, 2xGbE; Audio, 2xCOM, VGA, Connectors for USB Flash, 4x SATA, Fan

CP-RIO6-A-216
Similar to CP-RIO6-A, but PICMG 2.16 compliant; without external Ethernet ports

CP-RIO6-M
4HP Rear I/O Module for CP6005(X)-SA with 2 disk sockets

Need storage - try Innodisk SSD