Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
MEN Mikro

MEN Mikro M33

8 Analog Outputs

8 current or voltage outputs, 12 bits resolution
 
MEN Mikro M33 8 Analog Outputs
  
  • 8 current or voltage outputs
  • 12 bits resolution
  • 10 μs acquisition/conversion time
  • Simultaneous channel update
  • Optical isolation
  • -40 to +85°C screened versions
  • ROHS compliant



Datasheet/Manual:

MEN M33 datasheet in PDF format Datasheet in PDF format
Manual available on request Manual available on request

 

Introduction

The M33 is a highly flexible M-Module™ for analog output signals. The isolated supply voltages can be generated by an on-board DC/DC converter. The output voltage range can be set to 0..10V, -5..+5V or -10..+10V for each channel by software. In addition, the current outputs can be used with 0..20mA or 4..20mA. The output load is driven to ground. Attention: An external supply is needed with 8 current outputs!

The M33 is based on the M-Module™ ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module™ carrier cards in 3U, 6U and other formats are available from MEN or other manufacturers.
 
 

Specification

D/A Conversion:

8 channels
12 bits
DAC conversion time 10μs
±5 LSB gain
Simultaneous update of all channels possible

Voltage Output:

Output current: 5mA max.
Output linearity: ±1 LSB
Accuracy: ±0.2%, ±1 LSB differential
Voltage ranges: 0..10V; -5V..+5V; -10V..+10V
Voltage output stable up to 1μF capacitive load

Current Output:

Accuracy: ± 0.5%
Current range: 0..20mA; 4..20mA
Max. output voltage 10V
Load resistance range: 0..500 Ohm

Slew Rates for Voltage Output:

0V..+10V mode: switch from 0V to +10V; slew rate (SR) = 4V/μs
-5V..+5V mode: switch from -5V to +5V; slew rate (SR) = 4V/μs
-10V..+10V mode: switch from -10V to +10V; slew rate (SR) = 4V/μs

Peripheral Connections:

Via front panel on a shielded 25-pin D-Sub receptacle connector
Via carrier board (rear I/O)

M-Module™ Characteristics:

A08, D16, IDENT

Electrical:

Isolation voltage: 500V DC between M-Module™ interface and analog input connector
Supply voltage/power consumption:

  • +5V (4.85V..5.25V), 480mA quiescent current, 600mA with 8 channels voltage output, 650mA with 4 channels current output
  • External supply voltage +24V: 15.6V..30V

MTBF: 200,000h @ 50°C (derived from MIL-HDBK-217F)

Mechanical:

Dimensions: conforming to M-Module™ Standard
Weight: 80g

Environmental:

Temperature range (operation):

  • 0 to +60°C or -40°C to +85°C
  • Industrial temperature range on request
  • Airflow: min. 10m³/h

Temperature range (storage): -40..+85°C
Relative humidity range (operation): max. 95% non-condensing
Relative humidity range (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request

Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers

EMC:

Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)

Software Support:

MEN Driver Interface System (MDIS™ for Windows®, Linux, VxWorks®, QNX®, OS-9®)

ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:

Board:

04M033-10 4 analog outputs, 0 to +60°C
04M033-11 4 analog outputs, -40 to +85°C screened
04M033-12 8 analog outputs, 0 to +60°C
04M033-13 8 analog outputs, -40 to +85°C screened

Accessories:

05M000-00 M-Module cable, 2m, with 25-pin D-Sub plug/housing to pig tail
05M000-17 25 mounting screw sets to fix M-Modules on carrier boards

Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2012 Diamond Point International. All rights reserved.