Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
MEN Mikro

MEN Mikro M43

32-bit TTL I/O Interface

32 TTL inputs/outputs, -40 to +85°C screened versions
 
M58
  
  • 32 TTL inputs/outputs
  • Output current per pin: max. 25 mA
  • Active terminators
  • Same line interface as SCSI
  • Fast 16-bit host access
  • -40 to +85°C screened versions
  • ROHS compliant



Datasheet/Manual:

MEN M58 datasheet in PDF format Datasheet in PDF format
Manual available on request Manual available on request

 

Introduction

The M58 TTL I/O M-Module™ is used for fast and troublefree transmission of binary signals. It is organized in four 8-bit groups, where each group can be programmed as an input or output. Every group supports active termination, which can be activated by software. A trigger line allows simultaneous acquisition of the inputs of several groups - also on several modules - at a specific point of time. All port lines are ESD-protected, but not optically isolated.

The M58 is based on the M-Module™ ANSI mezzanine standard. It can be used as an I/O extension in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate M-Module™ carrier cards in 3U, 6U and other formats are available from MEN or other manufacturers.
 
 

Specification

Input/Output:

32-bit TTL I/O
Output current permanent per pin: max. 25mA
4 groups, alternatively input or output
Active terminators can be activated for each group
Output low current (VOL max. 0.55V): sink min. 25mA
Output high current (VOH min. 2.0V): source min. 25mA
Input high current: max. 100μA
Input low current: max. -100μA
Input voltage: min. -0.5V, max. 6V
Switching times:

  • Output low-to-high: tbd.
  • Output high-to-low: tbd.
  • Input: tbd.

Miscellaneous:

Trigger line with interrupt capabilities

Peripheral Connections:

Via front panel on a shielded 44-pin HD-Sub receptacle connector
Via carrier board (rear I/O)

M-Module™ Characteristics:

A08, D16, INTA, IDENT

Electrical:

Supply voltage/power consumption: +5V (-3%/+5%), 230mA typ. (idle), 1000mA max.
MTBF: 1,058,309h @ 40°C according to IEC/TR 62380 (RDF 2000)

Mechanical:

Dimensions: conforming to M-Module™ Standard
Weight: 68g

Environmental:

Temperature range (operation):

  • 0 to +60°C or -40 to +85°C (screened)
  • Airflow: min. 10m³/h

Temperature range (storage): -40 to +85°C
Relative humidity range (operation): max. 95% non-condensing
Relative humidity range (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10 to 150Hz
Conformal coating on request

Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers

EMC:

Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)

Software Support:

MEN Driver Interface System (MDIS™ for Windows®, Linux, VxWorks®, QNX®, OS-9®)

ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:

Board:

04M058-00 32-bit TTL I/O, 0..+60°C
04M058-02 32-bit TTL I/O, -40..+85°C screened

Accessories:

05M000-00 M-Module cable, 2m, with 25-pin D-Sub plug/housing to pig tail
05M000-17 25 mounting screw sets to fix M-Modules on carrier boards

Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2012 Diamond Point International. All rights reserved.