Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
Men Mikro

Men Mikro D3C

6U CompactPCI® MPC8245 SBC With PMC Expansion

Low Power, Up To 512MB Memory, Dual 10/100 LAN, Quad COM
 
Men Mikro D3C 6U PowerPC cPCI SBC
  
  • PowerPC® MPC8245 with 603e core
  • 1-slot CompactPCI® system slot
  • 512 MB DRAM, CompactFlash®
  • Graphics via PMC
  • Dual Fast Ethernet
  • 4 COMs, USB, IDE, keyboard/mouse
  • 2 PMC slots
  • MENMON™ BIOS for PowerPC® cards
  • -40 to +85°C screened versions



Datasheet/Manual:

MEN D3C datasheet in PDF format Datasheet in PDF format
Manual available on request Manual available on request

 

Introduction

The D3 is a single-board computer for embedded applications based on the MPC 8245 PowerPC®. It can be used in a CompactPCI® system slot or as a stand-alone card.

The D3 comes with the MPC8245 PowerPC® with 300MHz clock frequency and a local 32-bit/33-MHz PCI data bus. It is a complete state-of-the-art SBC offering DRAM, Flash and CompactFlash® memory, dual Fast Ethernet, 4 COMs, USB, IDE and keyboard/mouse interfaces as well as an optional onboard hard disk. In addition, the D3C CPU board can be equipped with PMC mezzanine cards. PMCs may particularly be used for intelligent telecom I/O. The modular combination of I/O functionality on a single-board computer allows to build up tailored control systems which appear as customized solutions based on standard components. Depending on the kind of I/O requirements, further standard versions of D3 are availabe for other mezzanine standards.

The D3 comes with MENMON™ support. MENMON™ is a sort of BIOS which can be used for bootstrapping operating systems (from disk, flash or network), for hardware testing, or for debugging applications without running any operating system.
 
 

Specification
CPU:

PowerPC®
o MPC8245
o 300MHz
o Double precision FPU
Memory:

L1 Cache integrated in MPC8245
Up to 512MB SDRAM system memory
o One 144-pin SO-DIMM slot for SDRAM modules
o 100MHz memory bus frequency
2MB Flash
Serial EEPROM 2KB for factory settings
CompactFlash® card interface
o Via on-board IDE
o Type I
o True IDE
Mass Storage:

IDE port for hard disk drives
o Drive can be connected via ribbon cable or mounted directly on the CPU board using MEN adapter kit
o Only one CompactPCI® bus slot needed even with hard disk
One IDE port for local CompactFlash®
I/O:

USB
o One USB 1.1 port
o Available via I/O connector
o External PHY
o Data rates up to 12Mbits/s

Ethernet
o Two 10/100Base-T Ethernet channels
o RJ45 connector at front panel with two LEDs

One RS232 UART (COM1)
o RJ45 connector at front panel
o 16-byte transmit/receive buffer
o Handshake lines: CTS, RTS; DCD, DSR, DTR

One UART (COM2)
o Accessible via I/O connector
o Physical interface using SA-Adapter™ via 10-pin ribbon cable on I/O connector
o RS232..RS485, isolated or not: for free use in system (e. g. cable to front)
o 16-byte transmit/receive buffer
o Handshake lines: CTS, RTS; DCD, DSR, DTR; RI

Two UARTs (COM3/COM4)
o Accessible via I/O connector
o Physical interface using SA-Adapter™ via 10-pin ribbon cable on I/O connector
o RS232..RS485, isolated or not: for free use in system (e. g. cable to front)
o Handshake lines: none

Keyboard/mouse
o PS/2 compatible
o External adapters for line drivers required

 
Mezzanine Slots:

Two PMC slots
o Compliant with PMC standard IEEE 1386.1
Miscellaneous:

Serial real-time clock with integrated 56-byte NVRAM
Serial hardware watchdog in supervisory circuit
Temperature sensor
User LEDs (external)
Hex switch for user settings
CompactPCI® Bus:

Compliance with CompactPCI® Core Specification PICMG 2.0 R3.0
System slot
32-bit/33-MHz PCI-to-PCI bridge
V(I/O): +3.3V (+5V tolerant)
PXI™:

Two trigger lines compliant with PXI™ Specification
Electrical Specifications:

Supply voltage/power consumption:
o +5V (-3%/+5%), 1.65A typ.
o ±12V for mezzanines only, tbd.
MTBF: 63,000h @ 50°C (derived from MIL-HDBK-217F)
Mechanical Specifications:

Dimensions: standard double Eurocard, 233.3mm x 160mm
Weight (without mezzanines and accessories): 315g
Environmental:

Temperature range (operation):
o 0 to +60°C or -40 to +85°C
o Airflow: min. 10m³/h
Temperature range (storage): -40..+85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request
Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC:

Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)
Software Support:

MENMON™
Linux
VxWorks®
QNX®
OS-9®
ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

02D003A00 D3B MPC8245 300 MHz, 0 MB RAM, 0 MB CF, 2 MB boot flash, 3 PC-MIP® expansion, 0 to +60°C
02D003A01 D3B MPC8245 300 MHz, 0 MB RAM, 0 MB CF, 2 MB boot flash, 3 PC-MIP® expansion, -40 to +85°C
02D003B00 D3B MPC8245 300 MHz, 0 MB RAM, 0 MB CF, 2 MB boot flash, 3 M-Modules™ expansion, 0 to +60°C
02D003B01 D3B MPC8245 300 MHz, 0 MB RAM, 0 MB CF, 2 MB boot flash, 3 M-Modules™ expansion, -40 to +85°C
02D003C00 D3B MPC8245 300 MHz, 0 MB RAM, 0 MB CF, 2 MB boot flash, 2 PMC expansion, 0 to +60°C
02D003C01 D3B MPC8245 300 MHz, 0 MB RAM, 0 MB CF, 2 MB boot flash, 2 PMC expansion, -40 to +85°C

Please refer to datasheet for further information.
Accessories:

N/A
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2008 Diamond Point International. All rights reserved.