Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
Men Mikro

Men Mikro F11N

3U CompactPCI®/PXI™ Pentium® III SBC

Pentium® III Up To 933 MHz , Up To 512MB DRAM, 128MB Flash
 
MEN F11N 3U cPCI Pentium III SBC
  
  • 32-bit 12 HP CompactPCI®/PXI™
  • System slot or stand-alone
  • ULP Pentium® III up to 933 MHz
  • ULV Celeron® up to 650 MHz
  • Up to 512 MB DRAM, 128 MB NAND Flash
  • 2 MB SRAM, CompactFlash®
  • 2 Fast Ethernet, COM1, 2 USB 1.1 (front)
  • Option: COM2 (front)
  • VGA, keyboard/mouse (front)
  • Up to 1600 x 1200 pixels
  • Prepared for 2.5" hard disk on board
  • FPGA - further programmable I/O functions



Datasheet/Manual:

MEN F11N datasheet in PDF format Datasheet in PDF format
Manual available on request Manual available on request

 

Introduction

Equipped with either an Intel® ULP Pentium® III or a ULV Celeron® processor core, the F11N single-board computer is a versatile 3U Eurocard CompactPCI® board, taking 8 HP or more front space depending on its configuration. A specially outlined heat sink efficiently takes away the heat from the board, even in extended temperature range. The F11N is designed especially for systems which require low power consumption, e.g. as a computing platform for rugged industrial PCs in mobile applications or for infotainment applications, offering the whole world of Windows® and Linux based software.

The F11N is controlled by an Ultra-Low Power Pentium® III with 933 MHz or an Ultra-Low Voltage Celeron® Processor with 400 MHz or 650 MHz. It provides 512 KB / 256 KB L2 cache. Together with the Pentium® III the 815E Intel® chip set is used.

The F11N provides dual Fast Ethernet via RJ45 connectors and COM1 via a D-Sub connector at the front. Two USB 1.1, graphics (VGA up to UXGA) and keyboard/mouse are also available at the front. The F11N has an SO-DIMM socket, a CompactFlash® socket, and it offers the possibility to mount a 2.5" hard disk on the board.

An on-board FPGA allows implementation of additional functionality such as AC'97 audio (with optical isolation), serial interfaces, CAN bus controllers, binary I/O, protocol converters, touch controller etc. to the needs of the individual application in a very flexible way. Before boot-up of the system, the FPGA is loaded from the boot Flash. Updates of the FPGA contents can be made inside the boot Flash during operation and are available after a re-boot of the system. The FPGA functions are physically implemented on SA-Adapters™. A maximum of 7 SA-Adapters™ can be realized on one F11N, with I/O accessible at the front panel.

The F11N also supports a rear I/O interface for IDE. The pin assignment is compatible with the rear I/O transition module of the F9 Pentium® M SBC. Equipped with a PCI-bridge chip, the F11N offers a full CompactPCI® interface (system slot functionality) for reliable system expansion. The generation of the 3.3 V supply voltage can optionally be made available out of the 5 V while the CompactPCI® system is supplied with 3.3 V.

Last but not least, the F11N's Award BIOS was especially designed for embedded system applications.
 
 

Specification
CPU:

Celeron® or Pentium® III
o 400MHz/650MHz or 933MHz processor core frequency
o 100MHz or 133MHz system bus frequency
o 33MHz APIC bus frequency
Memory:

Memory
256KB or 512KB L2 cache integrated in CPU
Up to 512MB SDRAM system memory
o One 144-pin SO-DIMM socket for SDRAM modules
o 133/100MHz memory bus frequency

CompactFlash® interface
o Type I
o True IDE

2MB SRAM
Up to 1GB soldered NAND Flash (and more), FPGA-controlled
Up to 16MB additional SDRAM, FPGA-controlled, e.g. for video data and NAND Flash firmware
2MB boot Flash
Mass Storage:

Parallel IDE (PATA)

  • One port for local CompactFlash®
  • One port for local hard-disk drive
  • Drive can be mounted directly on the CPU board

Up to 1GB soldered ATA NAND Flash (and more), FPGA-controlled
Graphics:

Integrated VGA graphics controller
VGA connector at front panel
Up to 1600 x 1200 pixels
USB:

Two USB 1.1 ports
Two Series A connectors at front panel
UHCI implementation
Data rates up to 12Mbits/s
Supplies High-Power (500mA) without external power supply
Ethernet:

Two 10/100Base-T Ethernet interfaces
Two RJ45 connectors at front panel
Four on-board LEDs to signal LAN Link and Activity status
I/O:

Two RS232 UARTs (COM1/COM2)
o COM1: 9-pin D-Sub connector at front panel
o COM2: Physical interface at front panel using SA-Adapter™ via 10-pin ribbon cable on I/O connector
o Data rates up to 115.2kbits/s
o 60-byte transmit/receive buffers
o Handshake lines: CTS, RTS; DCD, DSR, DTR
PS/2 keyboard/mouse
Front Connections:

VGA
Two USB 1.1 (Series A)
Two Ethernet (RJ45)
Two RS232 UARTs COM1/COM2 (D-Sub)
PS/2 keyboard/mouse
Rear I/O:

IDE
Other functions on request
Mainly compatible with F9 board
FPGA:

Standard factory FPGA configuration:
Main bus interface:
o 16Z125_UART - UART controller (controls COM1..COM2)
o 16Z058_SRAM - SRAM over SPI
o 16Z043_SDRAM - Additional SDRAM controller
o 16Z070_IDEDISK - IDE controller for NAND Flash
The FPGA offers the possibility to add customized I/O functionality. See FPGA.
Miscellaneous:

Real-time clock, backed up by the carrier board
Integrated hardware monitor
Reset button
4 FPGA-controlled LEDs
CompactPCI® Bus:

Compliance with CompactPCI® Core Specification PICMG 2.0 R3.0
System slot
Double-slot solution (plus 1 mechanical slot for hard disk)
32-bit/33-MHz PCI-to-PCI bridge
V(I/O): +3.3V or +5V (Universal Board)
PXI™

Prepared for four trigger lines compliant with PXI™ Specification R1.0
Available on request
Power:

Supply voltage/power consumption:
o +5V (-3%/+5%), 900mA typ. (Celeron® 400MHz), 1200mA typ. (Celeron® 650MHz), 1900mA typ. (Pentium® III 933MHz)
o +3.3V (-3%/+5%), 700mA typ. (Celeron® 400MHz), 700mA typ. (Celeron® 650MHz), 700mA typ. (Pentium® III 933MHz)
MTBF: 129,000h @ 40°C (derived from MIL-HDBK-217F)
Mechanical:

Dimensions: conforming to CompactPCI® specification for 3U boards
Weight: 560g (incl. heat sink, without hard disk)
Environmental:

Temperature range (operation):
0 to +60°C
Industrial temperature range on request
Airflow: min. 10m³/h
Temperature range (storage): -40..+85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request
Safety:

Electric strength: 500V AC (50Hz)
PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC:

Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst) with regard to CE conformity
BIOS:

Award BIOS
Software Support:

Windows®
Linux
VxWorks®
QNX® (on request)
RTX (on request)
ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

02F011N00 ULV Celeron® III 650MHz, for operation with rear-I/O card in 32-bit systems, 512MB SDRAM, 2MB SRAM, 128MB Nand flash, 2 Fast Ethernet, 1 COM, 2 USB 1.1, keyboard/mouse, VGA, 0..+60°C

02F011N02 ULV Celeron® III 650MHz, without rear I/O, 512MB SDRAM, 2MB SRAM, 128MB Nand flash, 2 Fast Ethernet, 1 COM, 2 USB 1.1, keyboard/mouse, VGA, 0..+60°C

02F011N03 ULP Pentium® III 933MHz, for operation with rear-I/O card in 32-bit systems, 512MB SDRAM, 2MB SRAM, 128MB Nand flash, 2 Fast Ethernet, 1 COM, 2 USB 1.1, keyboard/mouse, VGA, 0..+60°C

Please note that some of these options may only be available for large volumes. Please sales for more information.
Accessories:

N/A
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2008 Diamond Point International. All rights reserved.