Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
Men Mikro

Men Mikro F14

3U CompactPCIŽ/Express Pentium® M SBC

Intel® Core™ 2 Duo T7400 or L7400, Up To 2GB Soldered DDR2 Memory
 
MEN F14 3U cPCI Pentium M SBC
  
  • From ULV Celeron® M 373, 1 GHz
  • To Pentium® M 760, 2 GHz
  • PCI Express® four x1 links
  • 4 HP system master or stand-alone
  • 32-bit CompactPCI® or compactPCIe
  • Up to 2 GB DDR2 DRAM soldered
  • CompactFlash® slot
  • 2 SATA interfaces
  • Video via VGA and 2 SDVO2
  • Gigabit Ethernet (PCIe)
  • Up to 8 USB 2.0
  • High Definition audio
  • Board controller
  • -40 to +85°C screened versions



Datasheet/Manual:

MEN F14 datasheet in PDF format Datasheet in PDF format
Manual available on request Manual available on request

 

Introduction

Equipped with the high-performance Intel® 2-GHz Pentium® M down to the 1-GHz ultra low voltage Celeron® M processor, the single-board computer F14 is a versatile 4 HP / 3U (single-slot, single-size Eurocard) CompactPCI® board, designed especially for embedded systems which require high computing and graphics performance and low power consumption. All board versions come with tailored passive heat sinks within 4 HP height. Depending on the processor version forced air cooling is required inside the CompactPCI® system.

The F14 is suited for a wide range of industrial applications, for example for monitoring, vision and control systems as well as test and measurement. Main target markets comprise industrial automation, multimedia, transportation (railways, commercial vehicles), aerospace, shipbuilding, medical engineering and robotics. The robust design of the F14 together with the low-power Pentium® M processors make the board especially suited for use in rugged environments in mobile applications with regard to temperature, shock, vibration, humidity or dust according to the applicable DIN, EN or IEC industry standards. The F14 is also ready for coating so that it can be used in humid and dusty environments. The F14 offers a 32-bit/33-MHz interface to the CompactPCI® bus and can alternatively also be used without a bus system. In combination with a specific side card it can also perform system-slot functionality in a CompactPCI® Express system. Four PCI Express® links for high-speed communication requirements (such as Gigabit Ethernet, graphics) are supported on the board.

The DDR2 DRAM is soldered to F14 to guarantee optimum shock and vibration resistance. An IDE-driven robust CompactFlash® device offers nearly unlimited space for user applications. Apart from parallel ATA support, two serial ATA lines are also available.

The standard I/O available at the front panel of F14 includes graphics on VGA connector, two PCIe-driven Gigabit Ethernet interfaces (alternatively 1 Gigabit / 1 Fast Ethernet) as well as two USB 2.0 ports. The F14 can be extended by a side card to 8 HP. I/O functions realized on the side card include two digital video outputs for flat panel connection via DVI, another four USB 2.0 ports and HD Audio.The F14 is also prepared for rear I/O where for example another two USB 2.0 ports can be connected.

Two watchdogs for thermal supervision of the processor and board temperature as well as for monitoring the operating system complete the functionality of the F14. The F14 operates in Windows® and Linux environments as well as under major real-time operating systems like VxWorks® or QNX®. The Award BIOS was especially designed for embedded system applications. Equipped with Intel® components that come exclusively from the Intel® Embedded Line, the F14 has a guaranteed minimum standard availability of 5 years.
 
 

Specification
CPU:

ULV Celeron® M 373 up to Pentium® M 760
o 1.0 to 2.0GHz processor core frequency
o 400MHz or 533MHz front-side bus frequency
Chipset:

Northbridge: Intel® 915GM
Southbridge: Intel® ICH6M
Memory:

Up to 1MB L2 cache integrated in Celeron® M or 2MB L2 cache integrated in Pentium® M
Up to 2GB SDRAM system memory
o Soldered
o DDR2
o 400MHz or 533MHz memory bus frequency
o Dual-channel, 2x64 bits

4Mbits boot Flash
Serial EEPROM 2kbits for factory settings

CompactFlash® card interface
o Via on-board IDE
o Type I
o True IDE
o DMA support
Mass Storage:

Parallel IDE (PATA)

  • One IDE port for local CompactFlash®

Serial ATA (SATA)

  • Two channels via side-card connector
  • Transfer rates up to 150MB/s
Graphics:

Integrated in 915GM chipset
o Analog CRT DAC interface support
o Supports max. DAC frequency up to 400 MHz
o 24-bit RAMDAC support
o Maximum resolutions: 2048 x 1536 pixels 16M colors @ 75Hz refresh rate (analog); 1600 x 1200 pixels 16M colors @ 60Hz (digital)
o Incorporates PanelLink Digital technology (Silicon Image)
VGA connector at front panel
Two SDVO ports available via side-card connector
o Two additional DVI connectors at front panel optional via side card
o Simultaneous connection of two monitors
USB:

Two USB 2.0 ports via Series A connectors at front panel
Four USB 2.0 ports via side-card connector
Two USB 2.0 ports via rear I/O on request
UHCI implementation
Data rates up to 480Mbits/s
Ethernet:

Two 10/100/1000Base-T Ethernet channels, or: one 10/100/1000Base-T and one 10/100Base-T channel
RJ45 connectors at front panel
Gigabit Ethernet connected by two x1 PCIe® links
On-board LEDs to signal activity status and connection speed
Audio:

Accessible via side-card connector
Front Connections:

VGA
Two USB 2.0 (Series A)
Two Ethernet (RJ45)
Miscellaneous:

Board controller
Real-time clock, buffered by a GoldCap or alternatively a battery (5 years life cycle)
Watchdog timer
Temperature measurement
One user LED
Reset button
PCI Express®:

Two x1 links to connect local 1000Base-T Ethernet controllers
Two x1 links for extension through side-card connector, or:
Three x1 links if one Gigabit Ethernet channel is replaced by Fast Ethernet
Data rate 250MB/s in each direction (2.5 Gbits/s per lane)
CompactPCI® Bus:

Compliance with CompactPCI® Core Specification PICMG 2.0 R3.0
CompactPCI® Express support (EXP.0 R1.0)
System slot
32-bit/33-MHz CompactPCI® bus
V(I/O): +3.3V (+5V tolerant)
Busless Operation:

Board can be supplied with +5V only, all other voltages are generated on the board
Backplane connectors used only for power supply
Power:

Supply voltage/power consumption:
o +5V (-3%/+5%), approx. 2.5A (ULV Celeron® M 373), approx. 7.5A (Pentium® M 760)
o +3.3V (-3%/+5%), approx. 1A
o +12V (-10%/+10%), approx. 10mA
o If the board is supplied with 5V only (typically without a bus connection), the 3.3V are generated on the board and fed to the backplane (3A max.)
MTBF: 86,600h @ 40°C (derived from MIL-HDBK-217F)
Mechanical:

Dimensions: conforming to CompactPCI® specification for 3U boards
Weight: 370g
Environmental:

Temperature range (operation):
o 0..+45°C
o 0..+60°C (version with L7400 processor)
o Airflow: min. 15m³/h (1.5m/s)
Temperature range (storage): -40..+85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request
Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC:

Tested according to EN 55022 Class A (radio disturbance), EN 61000-4-2 (ESD), EN 61000-4-4 (burst) and EN 61000-4-5 (surge) with regard to CE conformity
BIOS:

Award BIOS
Software Support:

Windows®
Linux
VxWorks® (on request)
QNX® (on request)
ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

02F014-00 3 F14, CPCI 3U, Celeron M373 1GHz, 512MB DDR2, 0 to +60°C
02F014-01 3 F14, CPCI 3U, Pentium M760 2GHz, 1GB DDR2, 0 to +60°C
02F014-02 3 F14, CPCI 3U, Celeron M 1GHz, 512MB DDR2, -40°C to +85°C
02F014-13 3 F14, CPCI 3U, P M760,2GHz, 1GB DDR2, batt., 0 to +60°C

Please note that some of these options may only be available for large volumes. Please sales for more information.
Accessories:

02F600-00 2 COM extensions and SATA hard disk slot, for compatible SBCs, -40..+85°C screened
02F601-00 1 DVI-D and 1 audio at front, SATA hard disk slot, for compatible SBCs, 4HP, 0..+60°C
02F601-02 2 DVI-D, 1 audio, 1 COM (via SA-Adapter™) at front, SATA hard disk slot, for compatible SBCs, 8HP, 0..+60°C
02F602-00 3U CompactPCI® to CompactPCI® Express side card with 1 USB, 1 COM, 1 DVI, SATA hard disk slot, for compatible SBCs, 0..+60°C
02F603-00 3U CompactPCI® side card with 2 USB and 1 COM extension, SATA hard disk and CompactFlash® slot, for compatible
SBCs, mounted to the right of the SBC, 0..+60°C
02F604-00 3U CompactPCI® side card with 1 IEEE 1394 FireWire, 1 DVI, 1 HD audio and 1 COM extension, SATA hard disk slot, for F14 and compatible SBCs, mounted to the right of the SBC, 0..+60°C
02F605-00 1 XMC or PMC slot, for F14 and compatible SBCs, -40..+85°C with qualified components
02F606-00 2 Gigabit Ethernet on Lemo railway compliant connectors, 1 COM extension (SA-Adapter™ not included), SATA hard disk slot, for F14 and compatible SBCs, conformally coated, -40...+85°C screened
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2008 Diamond Point International. All rights reserved.