Call us: +44 (0)1634 300900 | E-mail: sales@dpie.com

Diamond Point International

MEN Mikro F751 - 3U cPCI/CompactPCI® DeviceNet Interface Board

According to ISO-11898, -40 to +85°C Operation

Introduction

The F751 is a single Eurocard CompactPCI® DeviceNet controller; that only requires one slot on the CompactPCI® bus.

It features a DeviceNet interface supporting an ISO high-speed of up to 500 kBit/s. The physical interface is isolated from the system.

Master or Slave protocol configuration can easily be done by loadable firmware. The complete protocol stack is executed on the F751, and data exchange to the host is done via Dual-Port-Memory or DMA.

The F751 is based on the netX SOC. This highly integrated network controller supports parallel data transmission via several data paths between the internal CPU and graphics engines, and the communication and host controllers. The netX SOC also controls the on-board memory and other peripheral interfaces such as UARTS, USB, SPI or I²C.

Communication works via a dual-port SRAM interface and is supported by window and pointer access mechanism. Interrupts are available in both directions from F751 to host and from host to F751.

The F751 supports a wide range of operating systems including Windows®, Windows® CE, Linux and VxWorks®.

The F751 has been designed for mission-critical industrial and for mobile applications with demand for high resistance regarding temperature, shock and vibration.

Specification

Interface

ConnectionsSupported communication determined by firmware:
• DeviceNet Master
• DeviceNet Slave

DeviceNet Interface
• Type ISO-11898
• Optically isolated
• CombiCon male connector, 5 pin

Communication Controller
• Hilscher netX 100 SOC

Integrated Memory
• 8 MB SDRAM
• 4 MB serial Flash EPROM
• 64 KB Dual-Port Memory (DPM)

Diagnostic Interface
• Mini B USB plug (5-pin)

LED Display
• System Status LED
• Module Network Status (duo LED)

General

ExpansionCompliant with PICMG 2.0 R2.1
32-bit/33-MHz bridge
DPM or DMA data access
ElectricalSupply voltage/maximum current
• +3.3 V DC ±5% / 650 mA
Connected via CompactPCI® Bus
MechanicalDimensions: 162.2 x 100 x 20 mm
Front panel: 4 HP with ejector
Conformal CoatingOn request
SoftwareWindows®
Windows® CE
Linux
VxWorks®
QNX®
TemperatureTemperature range (operation): -20..+70°C
Temperature range (storage): -10..+70°C
HumidityRelative humidity range (operation): max. 95% non-condensing
Relative humidity range (storage): max. 95% non-condensing
Weight134 g
Safety/CertificationThe device is certified according to UL 508
• UL-File-Nr. E221530
EMCEN 55011:2009 + A1:2010, CISPR 11:2009, Class A (radio disturbance)
EN 61000-4-2:2009 (electrostatic discharge)
EN 61000-4-3:2006 + A1:2008 + A2:2010 (radiated, radio-frequency, electromagnetic field immunity)
EN 61000-4-4:2004 + A1:2010 (burst electrical fast transients/burst)
EN 61000-4-5:2006 (surge)
EN 61000-4-6:2009 (to conducted disturbances, induced by radio- frequency fields)
EN 61000-4-8:2010 (power frequency magnetic field)
EN 61000-6-2:2005 + B1:2011 (for industrial environments)
Warranty2 Years
RoHSCompliant

Ordering Details

Board02F751-00
1 DeviceNet Slave interface, -20..+70°C screened

02F751-01
1 DeviceNet Master interface, -20..+70°C screened

This board can only be ordered together with one of the complete systems available from MEN
AccessoriesN/A