Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
Kontron Embedded Modules

Kontron DIMM-PC/ETH+COM & DIMM-PC/COM1

Module with 2 Serial Ports and Optional Ethernet Controller

Full PC functionality at the size of a business card
 
Kontron DIMM-PC/ETH+COM
  
  • 10Base-T Interface
  • Crystal Ethernet CS8900 IC
  • Plug & play or setup via software
  • Wide operating system support
  • Half and full duplex support
  • Adds 2 serial ports to system
  • Fully 16550 compatible UART's
  • Follows the IEEE802.3 standards
  • Wide operating system support



Datasheet/Manual:

Kontron DIMM-PC/ETH+COM datasheet in PDF format Datasheet in PDF format
Kontron DIMM-PC/ETH+COM manual in PDF format Manual in PDF format
 

Introduction

The DIMM-PC/ETH+COM is an add-on module for the Kontron® DIMM-PC® series. The Ethernet part is equipped with the Crystal LAN® CS8900 ISA Ethernet adapter from Crystal Semiconductor following the IEEE802.3 standard and supports half- or full-duplex operation in ISA Bus computers on 10 Mbps Ethernet networks. The controllers I/O addresses are software configurable via DOS setup program. The serial part is equipped with the SMC 37C665 I/O-controller and adds two more serial ports to a DIMM-PC® system. The signals of the serial ports are available on the DIMM-I/O connector in TTL levels. The customer can decide to use different types of interfaces (RS232, RS485, TTY etc.) by adding his own driver circuitry on his base board.

The DIMM-PC/ETH+COM is designed for a 144pin DIMM-connector known from notebooks as memory socket. Note that this connector is different to the used for the DIMM-PC/CPU itself. The pinout of DIMM-PC/CPU and DIMM-PC/ETH+COM are well considered, so an easy and short routing on the customers design is possible (a direct pin to pin connection).

With Kontron You stay...always a Jump ahead!
 
 

Specification
Board:

Uses Crystal LAN™ CS8900 Ethernet Controller
Ethernet Standards:

Follows the IEEE802.3 standards
Half and full duplex operation
10Mbps
Selectable I/O-address (set via software or plug and play
Serial Port:

2 serial interfaces
16550 compatible
Up to 115 kBaud
TTL signal levels
Add suitable transceiver to get RS-232, RS-422 or RS-485
Other:

Starter kit/baseboard available
Expansion:

DIMM-PC Interface

Size:

68x40 mm (2.7"x1.6")
Operating Systems:

Ethernet Drivers for
Windows 3.11, 95, 98, NT, and 2000
Windows CE v2.x and v3.x, embedded Windows NT
Linux, SCO Unix, pSOSystem, VxWorks
Power:

+5V +/- 5%.
Low power CMOS
90mA non active
120mA when active

Environment:

Temperature operation: 0° to 60°C, storage: -10° to 85°C
Humidity operation: 10% to 90%, storage: 5% to 95% (non condensing)
Shock: 50G/20ms squareware maximum.
Vibration: 16/0-600Hz, dwell not to exceed.

ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

08006-0000-02-0 DIMM-PC/COM1 Two serial interfaces
08006-0000-04-0 DIMM-PC/ETH+COM Ethernet controller and two serial interfaces

Please note that boards are supplied with no cables, software or manuals.
Software/manuals are available electronically.
Accessories:

08005-0000-00-5 DIMM-PC/KIT3 - Starter Kit with baseboard, DIMM-PC/VGA2 module and cables
08005-0000-00-4 DIMM-PC/ADA3 - Evaluation baseboard for DIMM-PC

SPCDIMM Socket for DIMM-PC-PC/CPU, 144pin
SIODIMM Socket for DIMM-PC-I/O, 144pin

96047-0000-00-0 JRC1 Remote Control Software with serial cable
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2009 Diamond Point International. All rights reserved.