Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
Kontron Embedded Modules

Kontron ETX-CD

All-In-One PC module with Intel® Core™ Duo technology

1.06GHz, 1.5GHz or 1.66GHz CPU Processor Versions
 
Kontron ETX-CD
  
  • With Intel® Core™ Duo processor
  • 1.06GHz, 1.5GHz 1.66GHzCPUs
  • Intel 945GM chipset
  • Intel GMA950 graphics
  • Upto 2GB DDR2-SDRAM
  • CRT and LCD support
  • LVDS LCD support, DVO option
  • Low profile board, 10mm height
  • ISA and PCI signals through headers
  • Intel 10/100Base-T Ethernet
  • Standard PC I/O & quad USB 2.0
  • Onboard AC97 VIA sound, SATA
  • Evaluation/adapter board available



Datasheet/Manual:

Kontron ETX-CD datasheet in PDF format Datasheet in PDF format
Kontron ETX-CD manual in PDF format Manual in PDF format
Kontron ETX Design Guide in PDF format ETX Design Guide in PDF format
 

Introduction

ETX-CD SATA headersETX-CD is the new highest performing Computer On Module based on ETX 3.0 standard. The new ETX-CD module is based on the Intel® Core™ Duo processor and Intel® Celeron® M processor as well as the Intel 945GM and ICH7M chipset.

ETX-CD modules will provide the following interfaces that are always located in the same physical position on each board, thus guaranteeing scalability between modules: PCI 2.3, USB 2.0, Parallel ATA, LVDS as well as an ACPI (Advanced Configuration and Power Interface) for optimised power management.

The JILI display interface technology ensures automatic setting of the video controller parameters for the attached LCD panel. The mounting holes on the board provide secure mounting to allow the module increased shock and vibration resistance.

It also takes advantage of the new ETX® 3.0 specification that allow for 2 Serial ATA ports without violating the existing ETX® 2.8 pin usage (see picture on right).

With Kontron You stay...always a Jump ahead!

Heatspreader Concept

ETX heatspreaderThe heat-spreader is a 2mm thick aluminium plate. It provides a thermal interface surface for heat removal from the ETX module. The heat-spreader is thermally coupled to the CPU die or package surface, and it may also be coupled to other heat generating devices on the module (e.g. chipset, vga chip). The heat spreader is not intended as a heat sink, although it may be suitable for this purpose on low power modules operating under benign conditions. Higher power modules or higher temperature conditions will probably require heat removal devices (e.g. heat sink with fan, heat pipe, larger heatsink etc.) to be attached to the heatspreader, or it may need to be thermally coupled to a chassis.

Supported Flat Panels

The list of supported panels is now too large to show in a single webpage, they are now shown in the 'flat panel selector'. To run the flat panel selector, click here and choose the ETX-CD as the model to see what panels are supported.

 
 

Specification
CPU:

Intel® Celeron® M processor ULV 423 (1.06 GHz, 533FSB, 1MB L2)
Intel® Core™ Duo processor L2400 LV (2x 1.66 GHz (dual core), 667FSB, 2MB L2)
Intel® Core™2 Duo processor L7400 LV (2x 1.5 GHz (dual core), 667FSB, 4MB L2)
Chipset:

Intel® 945GM 667/533 MHz FSB, Intel® ICH7M
DRAM:

Up to 2 GB DDR2 (400/533/667) SODIMM memory
Drives:

2x Serial ATA® II (300MB/s), (AHCI) ports (ETX 3.0 compliant)
IDE 2x EIDE UDMA 66/100
Ethernet:

10/100 MBit Base-T-Phy
Sound:

AC 97 controller, Line In, Line Out, Mic in
I/O Ports:

USB 4x USB 2.0 (OHCI / EHCI)
Enhanced Parallel Port (Shared with Floppy)
Floppy Port (Shared with LPT)
Graphics:

Integrated with Intel® Graphics Media Accelerator (GMA950)
Dual Independent Display Support
CRT and LVDS Resolutions:

  • Max CRT WUXGA/QXGA (2048x1536)
  • Max LCD WUXGA/UXGA (1600x1200), (JILI3/EDID support)
Other:

IDA Support, IrDA1.1 enhanced, WakeOnLAN, Watchdog, I²C Bus, RTC
E²PROM BIOS Setup, LAN Boot, JRC support, Suspend states (S0/S3/S4/S5)
Evaluation baseboard available
Remote control software available
Expansion:

ETX Interface (version 3.0 compliant)
PCI 2.3, 32 bit / 33 MHz PCI bus
Size:

95 x 114mm (3.7x4.5“)
Operating Systems:

Windows® XP Embedded
Windows® XP
Windows® CE (free toolkit available - supports .NET)
Linux
DOS
Power:

Estimated 10,5 W @ 5V with 1,66 GHz
Environment:

Temperature: operation: 0° to 60°C,storage: -10° to 85°C
Max. humidity: (not condensing): operation:5% to 90%, storage: 5% to 95% (non condensing)

ROHS Status:

This product is lead free/ROHS compliant.


Ordering Details:
Board:

18030-0000-11-1 ETX-CD with Intel® Celeron® M processor ULV 423 (1.06GHz, 533FSB, 1MB L2)
18030-0000-17-2 ETX-CD with Intel® Core™ Duo Processor L2400 (1.66GHz dual core, 667FSB, 2MB L2)
18030-0000-15-3 ETX-CD with Intel® Core™2 Duo Processor L7400 (1.5GHz dual core, 667FSB, 4MB L2)

Modules expected Q2 2007 (samples expect April)

The ETX-CD modules do not come with a heatspreader

Please note that boards are supplied with no cables, software or manuals.
Software/manuals are available electronically.
Accessories:

97011-2560-00-0 DDR2 SDRAM-256MB SODIMM MODULE
97011-5120-00-0 DDR2 SDRAM-512MB SODIMM MODULE
97011-1024-00-0 DDR2 SDRAM-1GB SODIMM MODULE
97011-2048-00-0 DDR2 SDRAM-2GB SODIMM MODULE

18010-0000-00-S ETX Starter Kit

Starter kit contains ETXeval board,CD-ROM, no memory, FDD, docs & PSU (add ETX module, DRAM & heatspreader to suit)

18030-0000-99-0 HSP-ETX CD threaded stand off heatspreader
18030-0000-99-1 HSP-ETX-CD through hole stand off heatspreader

18010-0000-00-0 ETXeval - ATX ETX Evaluation Board
96047-0000-00-0 JRC1 Remote Control Software with serial cable

18011-0000-00-0 ETX SAMPLE SMT receptacle connector for ETX (2.5mm tall, 4 pcs)
18011-0000-00-1 ETX SMT receptacle connector for ETX (2.5mm tall, 1000 pcs)
18011-0000-01-0 ETX SAMPLE SMT receptacle connector for ETX (9.5mm tall, 4 pcs)
18011-0000-01-1 ETX SMT receptacle connector for ETX (9.5mm tall, 500 pcs)
Each ETX module requires 4 of these connectors - most customers use 2.5mm version

18017-0000-00-0 ETX MOUNTING KIT (For one board, 2.5mm height)
18017-0400-00-0 ETX MOUNTING KIT (For 100 boards, 2.5mm height)
18017-1000-00-0 ETX MOUNTING KIT (For 1000 boards, 2.5mm height)
18017-0095-00-0 ETX MOUNTING KIT (For one board, 9.5mm height)
18017-1094-00-0 ETX MOUNTING KIT (For 1000 boards, 9.5mm height)
ETX mounting kit is for ETX boards with standard threaded heatspreaders
2.5mm version contains per board four of: 2.5mm screws, 3mm spacers & washers
9.5mm version contains per board four of: 2.5mm screws, 9.5mm spacers & washers
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2008 Diamond Point International. All rights reserved.