Diamond Point International
 
Kontron Embedded Modules

Kontron ETX-LX

ETX with 500 MHz AMD LX800 CPU, graphics & more

Low powered but high performance

 
Kontron ETX-LX
 
  • AMD LX800 CPU 500MHz CPU
  • Low profile board, just 10mm
  • ISA & PCI signals through headers
  • Low power consumption, low cost module
  • Extended temperature option available
  • Up to 1GB DDR-SDRAM
  • Compact flash socket
  • 10/100Base-T Ethernet
  • Onboard graphics, LCD support (LVDS or TTL)
  • Standard PC I/O, 2 SATA channels
  • Sound, 4x USB2 channels
  • Evaluation/adapter board available



Datasheet/Manual:

Kontron ETX-LX datasheet in PDF format Datasheet in PDF format
Kontron ETX-LX manual in PDF format Manual in PDF format
Kontron ETX Design Guide in PDF format ETX Design Guide in PDF format
ETX Specification in PDF format ETX Specification in PDF format

 

Introduction

The ETX-LX (Embedded Technology eXtended) is a highly integrated and fast PC module with extreme low power consumption. It is the RoHS alternative for ETX-mgx and more. It allows, due to the used AMD LX800 processor, the usage of the board without active cooling in applications, where space ETX-LX SATA Headerslimitations (the maximum height without heat sink is only 10 mm!) are major requirements. Despite the very little board dimensions, the EXT-LX offers all standard interfaces such as sound, Ethernet, USB2.0, graphic and TVout. The AC97 compatible sound chip is supported by most operating systems. For networking purposes the ETX-LX comes with a 10/100 MBit Ethernet controller.

You´re looking for a secure and EMI tolerant boot medium and want to be unlimited in your media capacity choice? A CompactFlash™ socket is already mounted on the ETX-LX and offers you a lot of possibilities. For further expansions two IDE ports with Ultra66 DMA capabilities are available. They do not provide the PCI bus only, the ISA bus signals are also available. A lot of existing ISA boards can still be used via an ISA slot on a baseboard. This avoids expensive redesigns and well proven ISA cards to PCI versions for standard PC motherboards. Despite the unbelievable variety of functionality, the EXT-LX is a very inexpensive choice, the cost effectiveness of this device is unbeatable. It also takes advantage of the new ETX 3.0 specication that allow for 2 Serial ATA ports without violating the existing ETX 2.8 pin usage (see picture on right)

ETX modules are like components, plugging in to an application-specific baseboard. The ETX modules supply the core CPU and memory subsystems together with sound, SVGA, Ethernet and standard PC I/O. They connect to the rest of the embedded system through high-density, low profile, surface-mount connectors, which carry both ISA and PCI bus signals as well as dedicated I/O interfaces. The mechanics of the interconnection is such that an ETX/ baseboard combination is virtually the same as height a one-board solution. ETX modules are scaleable and interchangeable, and they make possible the rapid development of semi-custom solutions for embedded applications .... always a Jump ahead!

With Kontron You stay...always a Jump ahead!

Heatspreader Concept

ETX heatspreaderThe heat-spreader is a 2mm thick aluminium plate. It provides a thermal interface surface for heat removal from the ETX module. The heat-spreader is thermally coupled to the CPU die or package surface, and it may also be coupled to other heat generating devices on the module (e.g. chipset, vga chip). The heat spreader is not intended as a heat sink, although it may be suitable for this purpose on low power modules operating under benign conditions. Higher power modules or higher temperature conditions will probably require heat removal devices (e.g. heat sink with fan, heat pipe, larger heatsink etc.) to be attached to the heatspreader, or it may need to be thermally coupled to a chassis.

Kontron have two different heatspreaders for the ETX-LX. One with threaded post and one with through hole posts. Drawings of the assemblies are available on request

Supported Flat Panels

The list of supported panels is now too large to show in a single webpage, they are now shown in the 'flat panel selector'. To run the flat panel selector, click here and choose the ETX-LX as the model to see what panels are supported.

 
 

Specification

CPU:

AMD LX800 CPU 500MHz, with integrated graphic
Refer to the ETX Product Line Performance document for benchmark figures

Chipset:

AMD® Geode™ CS5536 Companion Device

DRAM:

1 DDR-DIMM socket, max. 1GByte DDR-SDRAM

Cache:

Cache 16 kByte 1st Level

Drives:

CompactFlash™ socket on board
2x EIDE interface Ultra66 DMA mode
2x SATA interfaces (150mb/sec)
Shared floppy interface.

Ethernet:

10/100Base-Tx, Intel 82551ER

I/O Ports:

2x TTL Serial Ports (16550 compatible)
EPP/ECP, bi-directional parallel port
4x USB 2.0 (EHCI)
AC97 sound controller, line-input / output and microphone

Graphics:

CRT: SXGA (1280x1024) with 16 Bit
LCD: UXGA (1600x1200) with 16 Bit
Versions for LVDS and TTL (digital) LCD displays

Other:

Evaluation baseboard available
Remote control software available

Expansion:

ETX Interface

Size:

95 x 114mm (3.7x4.5“)

Operating Systems:

Compatible Operating Systems
Windows® XP Embedded
Windows® XP
Windows® CE (free toolkit available - supports .NET)
Windows 98 (limited support for most interfaces including video - contact for details)
Windows® 2000
VxWorks (BSP for VxWorks 6.5)
Linux
DOS
Contact us for others

Power:

All ETX modules are 5V powered

 
WinXP
100% Load
WinXP
Idle
Standby
S1
Standby
S3 Hot
Standby
S5
DOS
Prompt
500 MHz AMD LX800
7.98W
6.62W
5.99W
TBD
0.14W
7.47W

Refer to the ETX Product Line Power Consumption document for further details (inc idle/standby/suspend/speedstep)

Environment:

Temperature operation (standard): 0° to 60°C
Temperature operation (EXT version): -25° to 75°C
Temperature storage: -30° to 85°C
Humidity operation: 10% to 90%, storage: 5% to 95% (non condensing)

ROHS Status:

This product is lead free/ROHS compliant.


Ordering Details:

Board:

18027-0000-50-4 ETX-LX 500 MHz AMD LX800 CPU, graphic, sound, Ethernet and LVDS LCD
18027-0000-50-5 ETX-LX 500 MHz AMD LX800 CPU, graphic, sound, Ethernet and TTL LCD

18027-0000-50-4EXT ETX-LX 500 MHz AMD LX800 CPU, graphic, sound, Ethernet and LVDS LCD, -25° to 75°C
18027-0000-50-5EXT ETX-LX 500 MHz AMD LX800 CPU, graphic, sound, Ethernet and TTL LCD, -25° to 75°C

Please note that boards are supplied with no cables, software or manuals.
Software/manuals are available electronically.

The ETX-LX modules come without a heatspreader (see accessories)

Please note that boards are supplied with no cables, software or manuals.
Software/manuals are available electronically.

Accessories:

18027-0000-99-0 HSP-LX 2.5mm threaded heatspreader
18027-0000-99-1 HSP-LX 2.5mm through hole heatspreader

Kontron DRAM:
97007-2560-00-0 DDR-SODIMM memory module with 256 MByte (0° to 60°C)
97007-5120-00-0 DDR-SODIMM memory module with 512 MByte (0° to 60°C)
97007-1024-00-0 DDR-SODIMM memory module with 1 GByte (0° to 60°C)

Swissbit DRAM:
601403 SDN03264G1C61MT-60R DDR SODIMM 256MB 333/CL2.5 SMT STD TEMP 0° to 70°C
602360 SDN03264O3BK1MT-60R DDR SODIMM 256MB 333/CL2.5 COB STD TEMP 0° to 70°C
602364 SDN03264O3BK1MT-60IR DDR SODIMM 256MB 333/CL2.5 COB EXT TEMP -40° to 85°C
402070 SDN06464S4B51MT-60R DDR SODIMM 512MB 333/CL2.5 COB STD TEMP 0° to 70°C
402220 SDN06464S4B51MT-60IR DDR SODIMM 512MB 333/CL2.5 COB EXT TEMP -25° to 85°C
601215 SDN06464A1B61MT-60R DDR SODIMM 512MB 333/CL2.5 SMT STD TEMP 0° to 70°C
402221 SDN12864S4B52MT-60IR DDR SODIMM 1GB 333/CL2.5 COB STD TEMP -25° to 85°C
402071 SDN12864S4B52MT-60R DDR SODIMM 1GB 333/CL2.5 COB STD TEMP 0° to 70°C
601409 SDN12864L1B62MT-60R DDR SODIMM 1GB 333/CL2.5 SMT STD TEMP 0° to 70°C

18010-0000-00-S ETX Starter Kit

Starter kit contains ETXeval board,CD-ROM, no memory, FDD, docs & PSU (add ETX module, DRAM & heatspreader to suit)

18010-0000-00-0 ETXeval - ATX ETX Evaluation Board
96047-0000-00-0 JRC1 Remote Control Software with serial cable

18011-0000-00-0 ETX SAMPLE SMT receptacle connector for ETX (2.5mm tall, 4 pcs)
18011-0000-00-1 ETX SMT receptacle connector for ETX (2.5mm tall, 1000 pcs)
18011-0000-01-0 ETX SAMPLE SMT receptacle connector for ETX (9.5mm tall, 4 pcs)
18011-0000-01-1 ETX SMT receptacle connector for ETX (9.5mm tall, 500 pcs)
Each ETX module requires 4 of these connectors - most customers use 2.5mm version

18017-0000-00-0 ETX MOUNTING KIT (For one board, 2.5mm height)
18017-0400-00-0 ETX MOUNTING KIT (For 100 boards, 2.5mm height)
18017-1000-00-0 ETX MOUNTING KIT (For 1000 boards, 2.5mm height)
18017-0095-00-0 ETX MOUNTING KIT (For one board, 9.5mm height)
18017-1094-00-0 ETX MOUNTING KIT (For 1000 boards, 9.5mm height)
ETX mounting kit is for ETX boards with standard threaded heatspreaders
2.5mm version contains per board four of: 2.5mm screws, 3mm spacers & washers
9.5mm version contains per board four of: 2.5mm screws, 9.5mm spacers & washers

Order Online!

 

ORDER ONLINE - these products are available to order on our online webshop.

Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.

 
© 2012 Diamond Point International. All rights reserved.