Call us: +44 (0)1634 300900 | E-mail: sales@dpie.com

Diamond Point International

Diamond Systems Onyx-MM - 48-line Digital I/O + Counter/Timer PC/104 Module

48 Digital I/O Lines, 3 16-Bit Counter / Timers

Introduction

Extensive software control of features is the highlight of this digital I/O module featuring 48 digital I/O lines, 3 16-bit counter/timers, and 3 independent PC bus interrupt inputs.

The 48 digital I/O lines on Onyx-MM are based on 2 82C55 ICs. They can be programmed for input or output in groups of 8 lines. Direct as well as strobed (latched) I/O modes are supported, and all I/O lines are connected to 10K Ohm pull-up resistors.

The 3 16-bit counter/timers are based on an 82C54 IC. They are controlled through a configuration register on Onyx-MM (in addition to the standard 82C54 configuration register). The counter inputs can be switched between external signals, the on-board 4MHz clock oscillator, or counter outputs, all under software control. By using one counter's output as another counter's input, you can cascade counters in software to create a 32-bit or 48-bit counter.

Onyx-MM also features programmable interrupt operations. A second software-controlled register on board configures up to 3 interrupt lines on the PC bus. Interrupts can be generated by the counter/timer outputs, digital I/O lines, or an external input line. This allows you to use a counter to generate bus interrupts at a programmed periodic rate, generate hardware interrupts under software control, or generate interrupts in response to an external event.

Digital I/O Operation

Onyx-MM has 48 digital I/O lines using 2 82C55 ICs. Each chip has 24 I/O lines organized as three 8-bit ports, A, B, and C. All I/O lines are connected to 10KOhm pull-up resistors, and on power-up or system reset, all ports reset to input and are pulled high. A control register on the 82C55 chip allows you to program each port for input or output and for different operating modes, including basic I/O, strobed I/O, and bit set/reset.

Mode 0 operation provides basic input and output operations. No handshaking signals are used. This is the most common method of digital I/O and is useful for reading status signals, turning switches on and off, etc. All three ports can operate in Mode 0.

Mode 1 operation provides strobed I/O on ports A and B with handshaking signals provided on port C. In input mode, one signal acts as a strobe to latch data into the port, a second signal acts as an acknowledge output, and a third signal acts as an interrupt request. In output mode, one signal indicates that the CPU has written new data to the port, a second signal acts as an acknowledge input, and a third signal is used as an interrupt in response to the acknowledge input. This interrupt signal can be routed to one of the PC bus interrupt circuits on Onyx-MM through proper programming of the Onyx-MM interrupt configuration register described elsewhere on this page. Thus you can generate PC bus interrupts in response to new data being latched onto the board.

Mode 2 operation allows the use of Port A as a bi-directional data bus, with port C lines used for handshaking. Port A is normally in tristate mode. When the CPU writes new data to port A, an output signal indicates new data is available. In response, the external circuit strobes an acknowledge input signal, thereby enabling the output buffers on Port A. The external circuit can also latch new data into Port A with an input data strobe signal. Both input and output operations can be used to generate interrupts.

Bit set/reset mode enables individually setting (1) or resetting (0) any bit on Port C without having to read Port C and worry about masking or protecting unaltered bits. Note: The driver software shipped with Onyx-MM allows you to easily perform bit set and reset operations on any bit of any port.

Specification

Digital I/O/Counter/Timers

I/Os48, TTL/CMOS Compatible
InputsAll lines programmable for input in groups of 4 and 8
Pullup resistors: 10K? all input lines
Input voltage
• Low: -0.5V min, 0.8V max
• High: 2.0V min, 5.5V max
Input current: -200µA max (low), 2µA max (high)
OutputsAll lines programmable for input in groups of 4 and 8
Output voltage
• Low: 0.0V min, 0.4V max
• High: 3.0V min, Vcc -0.4V max
Output current: ±2.5mA max, each line
Counter/Timer(s)3 counter/timers, 16 bits wide
Connectors(s)Two identical 50-pin headers contain 24 digital I/O lines each, and a third 14-pin header is used for the counter/timer and external interrupt signals.
OtherInterrupt sources: Counter/timer outputs, Interrupt input, or DIO lines CO (programmable)

General

ExpansionStandard 8 bit PC/104 interface
ElectricalPower Input: +5VDC +/-5%
Consumption: 120mA typical all outputs open
MechanicalDimensions: 96mm x 90mm
Conformal CoatingOn request
SoftwareDOS
Linux
Windows XP
WES7
Windows 7
Windows CE.Net
Contact us for others
APIUniversal Driver 7.0
TemperatureTemperature range (operation): -40ºC to +85ºC (-40ºF to +185ºF)
Temperature range (storage): -40ºC to +85ºC (-40ºF to +185ºF)
Humidity0-90% non-condensing
Weight2.8 oz/79g
Warranty1 Year
RoHSCompliant

Ordering Details

BoardOMM-XT Onyx-MM 48 Digital I/O + 3 Counter/timers Extended Temperature
AccessoriesC-50-18 50-conductor 18" ribbon cable
C-14-18 14-conductor 18" ribbon cable
Order Online DSC Onyx-MM - Order Online