Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
Men Mikro

Men Mikro PP1

PCI-104 Module with PowerPC® MPC5200/B

Up To 128 MB SDRAM, Up To 16 MB Flash, 1 Fast Ethernet, Dual UART
 
Men Mikro PP1 - PCI-104 Module with MPC5200/B
  
  • PowerPC® MPC5200/B / 384 MHz
  • 32-bit/33-MHz PCI
  • Up to 128 MB SDRAM
  • Up to 16 MB Flash
  • Up to 64 KB FRAM
  • 1 Fast Ethernet, dual UART
  • Dual CAN with CANopen support
  • MENMON™ BIOS for PowerPC® cards
  • -40 to +85°C with qualified components



Datasheet/Manual:

MEN 0700-0012 datasheet in PDF format Datasheet in PDF format
Manual available on request Manual available on request

 

Introduction

The PP1 is controlled by an MPC5200/B PowerPC® that operates at 384 MHz. The complete PCI-104 module is exclusively available for -40 to +85°C operation temperature, as is the MPC5200 itself. The CPU consumes less than 1W at 384 MHz.

The PP1 provides up to 128 MB SDRAM for data and 16 MB Flash memory for program storage as well as 64 KB FRAM. The bus interface is a 32-bit 33-MHz PCI bus. The PP1 provides two optically isolated RS232 and one Fast Ethernet interface at its front panel. Two CAN controllers are included in the MPC5200. The physical CAN interface can be located on SA-Adapters™ or on the carrier board. The board also features a real-time clock and watchdog.

The PP1 comes with MENMON™ support. This firmware/BIOS can be used for bootstrapping operating systems (from disk, Flash or network), for hardware testing, or for debugging applications without running any operating system.

The PP1 is an industrial computer which is designed to operate under harsh environmental conditions. It complies with the PCI-104 specification and can be stacked with other PCI-104 boards or mounted on different types of carrier boards.
 
 

Specification
CPU:

PowerPC®
o MPC5200 or MPC5200B
o 384MHz
Memory:

Up to 128MB SDRAM system memory
o Soldered
o 64MHz memory bus frequency
16MB Flash
64KB non-volatile FRAM
Serial EEPROM 16kbits for factory settings
I/O:

Ethernet
o 10/100Base-T Ethernet
o 9-pin D-Sub connector at front panel

Two RS232 UARTs (COM1/COM2)
o One 9-pin D-Sub connector at front panel
o Data rates up to 115.2kbits/s
o 512-byte transmit/receive buffer
o Handshake lines: none

USB
o One USB 1.1 port
o Physical line interface via SA-Adapter™ on I/O connector P2
o OHCI implementation
o Data rates up to 12Mbits/s

Two independent CAN interfaces
o Physical line interface via SA-Adapters™ on I/O connector P2

Display interface
o Four characters, 5 by 7 pixels
o For additional display adapter PCB (on request)

8 GPIO lines
o Accessible via I/O connector P2
Front Connections:

One Ethernet (D-Sub)
Two RS232 UARTs COM1/COM2 (D-Sub)
PCI Interface:

32-bit/33-MHz PCI interface at PCI-104 connector J1
V(I/O): +3.3V (not +5V tolerant)
Compliant with PCI Specification 2.2
Support of one external master
Miscellaneous:

Real-time clock
Temperature sensor
Three push buttons and LED on optional display PCB (on request)
Electrical:

Supply voltage/power consumption:
o +5V, ±5%, 100mA typ.
o +3.3V, ±5%, 900mA typ.
MTBF: 450,000h @ 40°C (derived from MIL-HDBK-217F)
Mechanical:

Dimensions: conforming to PCI-104 specification
Weight: 90g
Environmental:

Temperature range (operation):
o -40..+85°C
o Airflow: min. 10m³/h
Temperature range (storage): -40..+85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request
Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC:

Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)
BIOS:

MENMON™
Software Support:

VxWorks®
Linux
CANopen firmware (Vector Informatik)
CANopen support: MEN Driver Interface System (MDIS™ for Windows®, Linux, VxWorks®, QNX®, OS-9®)
MSCAN/Layer2 support: MEN Driver Interface System (MDIS™ for Windows®, Linux, VxWorks®, QNX®, OS-9®)
ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

15PP01-00
MPC5200/384MHz, 32MB SDRAM, 16MB Flash, 64KB FRAM, -40..+85°C with qualified components

15PP01-05
MPC5200/384MHz, 128MB SDRAM, 16MB Flash, 64KB FRAM, -40..+85°C with qualified components

15PP01-07
MPC5200 Rev. B / 384MHz, 128MB SDRAM, 16MB Flash, 64KB FRAM, -40..+85°C with qualified components

Please refer to datasheet for further information.
Accessories:

0501-0002 Ethernet adapter D-Sub to RJ45 receptacle (cable 10cm)
0501-0003 Y-adapter RS232 D-Sub connector to dual D-Sub connector (cable 10cm)
05PP01-00 SA-Adapter™ kit for PP1 with 2 CAN and 1 USB 1.1 incl. cables; operation temperature -40..+85°C
08EK04-00 PCI-104 evaluation kit

Evaluation kit contains:

  • Mini ATX carrier board
  • PP1 with PowerPC® MPC5200/384MHz, 128MB DRAM, 16MB Flash, 64KB FRAM, 1 Fast Ethernet, 2 COMs, 0..+60°C
  • External PSU
  • SA-Adapter™ kit for 2 CAN and 1 USB 1.1
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2008 Diamond Point International. All rights reserved.