Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
MEN Mikro

MEN Mikro P598

Conduction-Cooled USM™ Main PMC
Main PMC for USM™ Universal Submodules
 
MEN P598 Conduction-Cooled USM Main PMC carrier
  
  • Main PMC for USM™ Universal Submodules
  • Conduction-cooled (CCPMC)
  • 1 USM™ slot
  • 1 FPGA 33,216 LE (for user-defined I/O and
    Nios® soft core)
  • 32 MB DDR2 SDRAM
  • 2 MB Flash
  • -40 to +85°C with qualified components
  • ROHS compliant



Datasheet/Manual:

MEN P598 datasheet in PDF format MEN Mikro P598 Datasheet - PDF
Manual available on request Manual available on request

 

Introduction

USM™ Universal Submodules make PMC modules more flexible than ever. The conduction-cooled main PMC P598 gets its specific function through the IP cores implemented inside the onboard FPGA. This function can be changed at any time through implementation of different IP cores. The corresponding line drivers are realized on the USM™ which is simply plugged on the P598. The same USM™ may also be used on convection-cooled PMCs and XMCs or main M-Modules™. A new design is then limited to the USM™ module and the FPGA content and therefore saves development time and costs. A Nios® soft processor implemented in the Cyclone® II FPGA by Altera® provides local intelligence where needed.

The growing range of Wishbone-based standard IP cores from MEN comprise different UARTs, Ethernet, fieldbus interfaces, digital I/O etc. For users that like to write and/or implement specific IP cores on their own a complete development kit is available. The kit is based on a function-identical convection-cooled PMC module with front I/O.

The USM™ concept has been developed for harsh environment. Therefore, the P598 uses robust connectors to the USM™, while all other components are soldered, and operates in a -40 to +85 °C temperature range with qualified components. The P598 is a conduction-cooled PMC mezzanine card suitable for any compliant host carrier board in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate carrier cards in 3U, 6U and other formats are available from MEN or other manufacturers.
 
 

Specification

Functionality:

User-defined through FPGA
Line drivers and/or additional hardware implemented on USM™ Universal Submodule (not included)

Memory:

332MB SDRAM memory

  • Soldered
  • DDR2
  • 132MHz memory bus frequency
  • FPGA-controlled

2MB non-volatile Flash

  • For FPGA data and Nios® firmware
  • FPGA-controlled

FPGA:

Standard factory FPGA configuration:

  • Main bus interface
  • Altera® SOPC Unit incl. Nios® II/f soft processor, GPIO, UART and DDR2 SDRAM control
  • Wishbone-to-Avalon®/Avalon®-to-Wishbone bridges
  • Chameleon Table V2
  • Interrupt controller, SMBus controller
  • PCI to Wishbone bridge, ID EEPROM emulation
  • 16Z045_FLASH - Flash interface
  • 16Z034_GPIO - GPIO controllers (2 IP cores, for onboard LEDs and 8-bit I/O)

The FPGA offers the possibility to add customized I/O functionality.

USM™ Slot:

One slot for a standard USM™ module
For implementation of line drivers and/or additional hardware

Miscellaneous:

Eight onboard LEDs, FPGA-controlled
I²C interface to detect the USM™ module

PMC Characteristics (PCI):

Compliant with PCI Specification 2.2
32-bit/33-MHz, 3.3V V(I/O)
Target

Peripheral Connections@

Via Pn4 rear I/O connector

Electrical:

Isolation voltage: Voltage depends on implementation and signal routing of USM™
Supply voltage/power consumption:

  • +5V (-3%/+5%), FPGA idle / US0 plugged: approx. 118mA, memory test / US0 plugged: 122mA
  • +3.3V (-5%/+5%), FPGA idle / US0 plugged: 76mA, memory test / US0 plugged: 82mA

Mechanical:

Dimensions: conforming to IEEE 1386.1
In accordance with VITA 20 (proposed Draft Standard for Conduction Cooled PMC)
Weight: 36g (w/o USM™ module)

Environmental:

Temperature range (operation):

  • -40 to +85°C (qualified components), conduction-cooled
  • Airflow: min. 10m³/h

Temperature range (storage): -40 to +85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request

MTBF:

848,597h @ 40°C according to IEC/TR 62380 (RDF 2000)

Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers

Software Support:

Flash update tools for Windows®, Linux, VxWorks®
Driver software depending on implemented FPGA functions

EMC:

Radio disturbance: no connection outside housing, therefore radio disturbance not relevant
ESD/burst: no external interface connector, therefore ESD and burst not relevant

ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

15P598-00 USM main PMC, conduction cooled, -40..+85°C with qualified components
Accessories:

19P599-00 PMC USM FPGA development kit consisting of 1 FPGA-based universal PMC P599, 1 bare USM Universal Submodule US0, 1 eval board AD99 for USM/FPGA development, 1 SA-Adapter SA1 (RS232), connection cable, FPGA/Nios example project including PCI core (key download), 0..+60°C

08US00-00 Universal Submodule for prototyping, -40..+85°C qualified
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2012 Diamond Point International. All rights reserved.