Diamond Point International

Sitemap - Print Page - Email Link - RSS News Feed RSS

 
MEN Mikro

MEN Mikro P699

USM™ Main XMC
Main XMC for USM™ Universal Submodules
 
MEN P599 Main PMC for USM Universal Submodules
  
  • Main XMC for USM™ Universal Submodules
  • PCIe® 2.5 Gbits/s
  • 1 USM™ slot
  • 1 FPGA 24,624 LE (for user-defined I/O)
  • 32 MB DDR2 SDRAM
  • 4 MB Flash
  • -10 to +70°C screened
  • ROHS compliant



Datasheet/Manual:

MEN P699 datasheet in PDF format MEN Mikro P699 Datasheet - PDF
Manual available on request Manual available on request

 

Introduction

USM™ Universal Submodules make XMC modules more flexible than ever. The main XMC P699 gets its specific function through the IP cores implemented inside the onboard FPGA. This function can be changed at any time through implementation of different IP cores. The corresponding line drivers are realized on the USM™ which is simply plugged on the P699. The same USM™ may also be used on PMCs, conductioncooled PMCs or M-Modules™ supporting the USM™ concept. A new design is then limited to the USM™ module and the FPGA content and therefore saves development time and costs. If local intelligence is needed, a Nios® soft processor can be implemented in the Cyclone® III FPGA on request.

The growing range of Wishbone-based standard IP cores from MEN comprise different UARTs, Ethernet, fieldbus interfaces, graphics, digital I/O etc. The USM™ concept has been developed for harsh environments. Therefore, the P699 uses robust connectors to the USM™, while all other components are soldered, and operates in a -10 to +70 °C temperature range.

The P699 is an XMC mezzanine card suitable for any compliant host carrier board in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Compared to PMC, the XMC standard defines a different board-to-board connector for support of PCI Express®. Appropriate carrier cards in 3U, 6U and other formats are available from MEN or other manufacturers.
 
 

Specification

Functionality:

User-defined through FPGA
Line drivers and/or additional hardware implemented on USM™ Universal Submodule (not included)

Memory:

32MB SDRAM memory

  • Soldered
  • DDR2
  • 133MHz memory bus frequency
  • FPGA-controlled

2MB non-volatile Flash

  • For FPGA data and Nios® firmware
  • FPGA-controlled

FPGA:

Standard factory FPGA configuration:

  • Chameleon Table V2
  • PCI Express® interface/PCIe® to Wishbone bridge
  • ID EEPROM emulation
  • 16Z069_RST - Reset controller
  • 16Z052_GIRQ - Interrupt controller
  • 16Z001_SMB - SMBus controller
  • 16Z126_SERFLASH - Serial Flash interface
  • 16Z043_SDRAM - DDR2 SDRAM controller
  • 16Z125_UART - UART controller
  • 16Z034_GPIO - GPIO controllers (3 IP cores, for onboard LEDs and 16-bit I/O)

The FPGA offers the possibility to add customized I/O functionality.

USM™ Slot:

One slot for a standard USM™ module
For implementation of line drivers and/or additional hardware

Miscellaneous:

Eight onboard LEDs, FPGA-controlled
I²C interface to detect the USM™ module

XMC Characteristics:

Compliant with XMC standard VITA 42.3-200x
PCI Express® links: one x1
Data rate 250MB/s in each direction (2.5 Gbits/s per lane)

Peripheral Connections:

Via front panel on a shielded 50-pin HP D-Sub SCSI 2 receptacle connector

Electrical:

Isolation voltage: Voltage depends on implementation and signal routing of USM™
Supply voltage/power consumption:

  • +5V and +12V (-5%/+5%)
  • +3.3V (-5%/+5%)
  • Consumption depends on FPGA and USM™ configuration

Mechanical:

Dimensions: conforming to IEEE 1386.1
Weight: 70g (w/o USM™ module)

Environmental:

Temperature range (operation):

  • -10 to +70°C (screened)
  • Airflow: min. 10m³/h

Temperature range (storage): -40 to +85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating on request

MTBF:

757,662h @ 40°C according to IEC/TR 62380 (RDF 2000)

Safety:

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers

Software Support:

Flash update tools for Windows®, Linux, VxWorks®
Driver software depending on implemented FPGA functions
UART driver software for Windows® on request

EMC:

Conforming to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)

ROHS Status:

This product is lead free/ROHS compliant.

Ordering Details:
Board:

15P699-00 USM main XMC, -10..+70°C screened
Accessories:

19P599-00 PMC USM FPGA development kit consisting of 1 FPGA-based universal PMC P599, 1 bare USM Universal Submodule US0, 1 eval board AD99 for USM/FPGA development, 1 SA-Adapter SA1 (RS232), connection cable, FPGA/Nios example project including PCI core (key download), 0..+60°C

08US00-00 Universal Submodule for prototyping, -40..+85°C qualified
05P599-00 PMC/M-Module cable, 2m, with 50-pin HP D-Sub 50 M both sides, 0..+60°C
Further Information:

Want further information or pricing on this product? Either fill out our feedback form or contact us for further information.
 
© 2012 Diamond Point International. All rights reserved.