Call us: +44 (0)1634 300900 | E-mail:

Diamond Point International

Trimble AV34 - High Performance GNSS (GPS and GLONASS L1/L2) Antenna

Supports GPS L1/L2, GLONASS L1/L2

Trimble AV34 - High Performance GNSS Antenna
Key Features
High Performance GNSS Antenna
GPS L1 + L2 / GLONASS L2 + L2
Low-profile Fuselage/Bulkhead Mounting
Sub-centimeter phase center repeatability
–55°C to +85°C temperature operation


The Trimble AV34 GNSS Antenna has been designed to support high accuracy aerial, land and marine applications in one compact design. The rugged 4 hole bulkhead mounting allows the antenna to be used in the most rugged of environments.

Comprehensive GNSS Support

The Trimble AV34 GNSS antenna offers support for both GPS and GLONASS L1/L2 signals. These are the optimum set of signals for your high accuracy RTK receiver. Dual frequency allows for faster initialization and dual constellation improves the number of satellites available for positioning, especially in obstructed environments.

Robust, Low-Multipath GPS Antenna

The antenna resists unwanted signal interference or multipath, which can cause inaccurate measurements. Multipath is caused by signals being reflected from surfaces such as the ground, surrounding trees, or buildings.


The antenna is an aviation type of design. The bulkhead mounting ensures only the rugged radome is exposed to the elements. This is an ideal design for customers building machine control systems. The antenna can be mounted flush with the vehicle surface or on the top of a pole mount. The TNC connector is located on the underside of the unit ensuring the attached cable is also protected from the environment.


Antenna Specification

ConnectorTNCF female signal connector
FrequencyL1 Band GNSS Frequency tracking Including:
• GPS: L1

L2 Band GNSS Frequency tracking Including:
• GPS: L2

Frequencies: 1551–1615 MHz, 1217–1260 MHz
Gain43 dB
Impendance50 Ohms
PolarizationRight Hand Circular
VSWRLess than or equal to 2.0:1
OtherQuality signal tracking
Small cross-sectional area to reduce wind loading
Low voltage, low power consumption
Integral low noise amplifier
Powered by GNSS receiver via coaxial cable
High gain for reliable tracking in difficult environments
4 recessed bulkhead mounting holes
Rugged radome designed for machine environments
Axial Ratio: 3dB Max @ boresight
Amplifier Noise Figure: 2.5 dBMax
Finish: UV resistant, high impact thermoplastic white radome with aluminum base


Electrical4.5 V DC to 18 V DC
Mechanical8.9 cm diameter, 2.1 cm height (3.5" diameter, 0.84" height)
TemperatureTemperature range (operation): -55 to +85°C
Temperature range (storage): -55 to +85°C
ConditionsDO-160D SectionString CategoryDescription


-55ºC to +85ºC,
10º/min, 2 cycles
Humidity - Method 507.4 MIL-STD-810-F
Shock - Method 516.5 MIL-STD-818-F
Procedure II
Vibration - Method 514.5C-3 MIL-STD-810-F
Section 514.5-CVII
HumiditySee above
Weight0.213Kg (0.44 lb)
Altitude16,764 m (55,000 ft)
VibrationSee above
ShockSee above
Warranty1 Year

Ordering Details

Board86362 Trimble AV34 L1/L2/G1/G2 Aviation Antenna
AccessoriesA02500 10m TNC-TNC Antenna Cable
64922-30 30m TNC-TNC Antenna Cable
84902 AV33/34 Antenna Bracket